Curtiss SB2C Helldiver

Here are some images of HPH Models 1/32 scale Curtiss SB2C Helldiver bomber.
With over 250 resin parts and hundreds of photoetched parts this kit is not for the weak. The resin parts fit was reasonably OK with no real issues other than the ones one would expect with a resin kit.
The most difficult part was building the all photoetched dive brakes. If ever there was a new term for the word fiddly this was it .
My only real complaint about the kit are the decals. For reasons best known to themselves they made the interior decals possible to remove individually with each decal having its own clear coat which is what one would naturally come to expect with decals in pretty much any kit nowadays. However as for the rest of the same decal sheet it was covered entirely with a clear coat forcing one to cut out each of the remaining decals to form, including the hundreds of stencil decals. A very tedious experience I assure you. However it turned out to be a fairly decent model worthy of any collection.

From Wikipedia"
The Curtiss SB2C Helldiver was a carrier-based dive bomber aircraft produced for the United States Navy during World War II. It replaced the Douglas SBD Dauntless in US Navy service. The SB2C was much faster than the SBD it replaced.
Crew nicknames for the aircraft included the Big-Tailed Beast (or just the derogatory Beast), Two-Cee and Son-of-a-Bitch 2nd Class (after its designation and partly because of its reputation for having difficult handling characteristics). Neither pilots nor aircraft carrier captains seemed to like it.
Delays marred its production—by the time the A-25 Shrike variant for the USAAF was deployed in late 1943, the Army Air Forces no longer had a need for a thoroughbred dive bomber. Poor handling of the aircraft was another factor that hampered its service introductions; both the British Royal Navy and the Royal Australian Air Force cancelled substantial orders.
The Truman Committee investigated Helldiver production and turned in a scathing report, which eventually led to the beginning of the end for Curtiss. Problems with the Helldiver were eventually ironed out, and in spite of its early problems, the aircraft was flown through the last two years of the Pacific War with a fine combat record.^[3]

The Helldiver was developed to replace the Douglas SBD Dauntless. It was a much larger aircraft, able to operate from the latest aircraft carriers and carry a considerable array of armament. It featured an internal bomb bay that reduced drag when carrying heavy ordnance. Saddled with demanding requirements set forth by both the U.S. Marines and United States Army Air Forces, the manufacturer incorporated features of a "multi-role" aircraft into the design.
The Model XSB2C-1 prototype initially suffered teething problems connected to its Wright R-2600 Twin Cyclone engine and three-bladed propeller; further concerns included structural weaknesses, poor handling, directional instability and bad stall characteristics. In 1939, a student brought a model of the new Curtiss XSB2C-1 to the MIT wind tunnel. Professor of Aeronautical Engineering Otto C. Koppen was quoted as saying, "if they build more than one of these, they are crazy". He was referring to controllability issues with the small vertical tail.
The first prototype made its maiden flight on 18 December 1940. It crashed on 8 February 1941 when its engine failed on approach, but Curtiss was asked to rebuild it. The fuselage was lengthened and a larger tail was fitted, while an autopilot was fitted to help the poor stability. The revised prototype flew again on 20 October 1941, but was destroyed when its wing failed during diving tests on 21 December 1941.
Large-scale production had already been ordered on 29 November 1940, but a large number of modifications were specified for the production model. Fin and rudder area were increased, fuel capacity was increased, self-sealing fuel tanks were added and the fixed armament was doubled to four 0.50 in (12.7 mm) machine guns in the wings, compared with the prototype's two cowling guns. The SB2C-2 was built with larger fuel tanks, improving its range considerably.
The program suffered so many delays that the Grumman TBF Avenger entered service before the Helldiver, even though the Avenger had begun its development two years later. Nevertheless, production tempo accelerated with production at Columbus, Ohio and two Canadian factories: Fairchild Aircraft Ltd. (Canada), which produced 300 (under the designations XSBF-l, SBF-l, SBF-3 and SBF-4E), and Canadian Car and Foundry, which built 894 (designated SBW-l, SBW-3, SBW-4, SBW-4E and SBW-5), these models being respectively equivalent to their Curtiss-built counterparts. A total of 7,140 SB2Cs were produced in World War II.
The U.S. Navy would not accept the SB2C until 880 modifications to the design and the changes on the production line had been made, delaying the Curtiss Helldiver's combat debut until 11 November 1943 with squadron VB-17 on Bunker Hill, when they attacked the Japanese-held port of Rabaul on the island of New Britain, north of Papua New Guinea. The first version of the SB2C-1 was kept stateside for training, its various development problems leading to only 200 being built. The first deployment model was the SB2C-1C. The SB2C-1 could deploy slats mechanically linked with landing gear actuators, that extended from the outer third of the wing leading edge to aid lateral control at low speeds. The early prognosis of the "Beast" was unfavourable; it was strongly disliked by aircrews due to its size, weight, and reduced range compared to the SBD it replaced.
In the Battle of the Philippine Sea, 45 Helldivers were lost because they ran out of fuel returning to their carriers.
Among its major faults, the Helldiver was underpowered, had a shorter range than the SBD, was equipped with an unreliable electrical system, and was often poorly manufactured. The Curtiss-Electric propeller and the complex hydraulic system had frequent maintenance problems. One of the faults remaining with the aircraft through its operational life was poor longitudinal stability, resulting from a fuselage that was too short due to the necessity of fitting on to aircraft carrier elevators. The Helldiver's aileron response was also poor and handling suffered greatly under 90 kn (100 mph; 170 km/h) airspeed; since the speed of approach to land on a carrier was supposed to be 85 kn (98 mph; 157 km/h), this proved problematic. The 880 changes demanded by the Navy and modification of the aircraft to its combat role resulted in a 42% weight increase, explaining much of the problem.
The solution to these problems began with the introduction of the SB2C-3 beginning in 1944, which used the R-2600-20 Twin Cyclone engine with 1,900 hp (1,400 kW) and Curtiss' four-bladed propeller. This substantially solved the chronic lack of power that had plagued the aircraft. The Helldivers would participate in battles over the Marianas, Philippines (partly responsible for sinking the battleship Musashi), Taiwan, Iwo Jima, and Okinawa (in the sinking of the battleship Yamato). They were also used in the 1945 attacks on the Ryuku Islands and the Japanese home island of Honshū in tactical attacks on airfields, communications and shipping. They were also used extensively in patrols during the period between the dropping of the atomic bombs and the official Japanese surrender, and in the immediate pre-occupation period.
An oddity of the SB2Cs with 1942 to 1943-style tricolor camouflage was that the undersides of the outer wing panels carried dark topside camouflage because the undersurfaces were visible from above when the wings were folded.
In operational experience, it was found that the U.S. Navy's Grumman F6F Hellcat and Vought F4U Corsair fighters were able to carry an equally heavy bomb load against ground targets and were vastly more capable of defending themselves against enemy fighters. The Helldiver, however, could still deliver ordnance with more precision against specific targets and its two-seat configuration permitted a second set of eyes. A Helldiver also has a significant advantage in range over a fighter while carrying a bombload, which is extremely important in naval operations.
The advent of air-to-ground rockets ensured that the SB2C was the last purpose-built dive bomber produced. Rockets allowed precision attack against surface naval and land targets, while avoiding the stresses of near-vertical dives and the demanding performance requirements that they placed on dive bombers 

U.S. Navy Curtiss SB2C-5 Helldivers of Attack Squadron 1A (VA-1A) "Tophatters" roll into dives to support amphibious forces during postwar landing exercise (1947)

The SB2C remained in active postwar service in active duty US Navy squadrons until 1947 and in Naval Reserve aviation units until 1950. Surplus aircraft were sold to the naval air forces of France, Italy, Greece, Portugal, and Thailand. Greek SB2Cs served in combat in the Greek Civil War with additional machine guns mounted in wing pods. French SB2Cs flew in the First Indochina War from 1951 to 1954.
Built at Curtiss' St. Louis plant, 900 aircraft were ordered by the USAAF under the designation A-25A Shrike. The first ten aircraft had folding wings, while the remainder of the production order omitted this unnecessary feature. Many other changes distinguished the A-25A, including larger main wheels, a pneumatic tailwheel, ring and bead gunsight, longer exhaust stubs, and other Army-specified radio equipment. By late 1943, when the A-25A was being introduced, the USAAF no longer had a role for the dive bomber, as fighter aircraft such as the Republic P-47 Thunderbolt had shown their ability to carry out tactical air support missions with great success.
After offering the Shrike to Australia, only ten were accepted before the Royal Australian Air Force rejected the remainder of the order, forcing the USAAF to send 410 to the U.S. Marines. The A-25As were converted to the SB2C-1 standard, but the Marine SB2C-1 variant never saw combat, being used primarily as trainers. The remaining A-25As were similarly employed as trainers and target tugs.